Guide: shop workflow
From Sketch to Cut List: Designing a Bookcase
A design is only useful in the shop once it becomes a list of parts and a plan for cutting them. This guide takes a simple plywood bookcase from a pencil sketch to a sheet layout, and shows where software saves material and mistakes.
This site is made by the FurniMesh team, and FurniMesh (furnimesh.com) is our own product. It plays no part in cut lists. Its one use here is reference: if you are matching an existing bookcase, the FurniMesh SKP library and photo-to-3D tool can give you a model to measure proportions against.

The project
A bookcase 36 inches wide, 72 inches tall and 11-1/2 inches deep, built from 3/4-inch plywood with a 1/4-inch plywood back. It has a fixed top and bottom, three adjustable shelves and a 3-inch toe kick. The carcass is 11-1/4 inches deep, and the 1/4-inch back is applied to the rear.
One practical note before modeling: most "3/4-inch" plywood is actually thinner, often around 23/32 inch. Measure your sheets with calipers and model to the real thickness, or your dados will be loose.
Sketch with the dimensions that matter
A paper sketch should fix only the decisions that drive everything else: overall size, material thickness and how the parts join. Here the top and bottom sit between the sides in 1/4-inch-deep dados. That decision sets the length of the top and bottom: 36 inches minus two 3/4-inch sides, plus two 1/4-inch dado depths, equals 35 inches. If you used butt joints instead, the length would be 34-1/2 inches. This is the kind of arithmetic a model checks for you.
Model each part as a component
In SketchUp, model every board as its own component and name it by function: Side, Top, Bottom, Shelf, Toe Kick, Back. Identical parts should be copies of one component so the cut list counts them correctly. Apply a material to each component, for example "Birch ply 3/4" and "Birch ply 1/4", because cut-list tools use materials to group parts by stock.
In Fusion, the equivalent is one component per part, with thickness driven by a parameter such as plyT = 0.72 in. Change the parameter when your sheets measure differently, and every dado updates.
Generate the parts list
With OpenCutList installed in desktop SketchUp, open its Cut List tab and generate. It reads each component's dimensions and groups parts by material. For this bookcase, the 3/4-inch plywood parts are:
| Part | Qty | Length | Width | Notes |
|---|---|---|---|---|
| Side | 2 | 72" | 11-1/4" | Dados for top and bottom, shelf-pin holes |
| Top and bottom | 2 | 35" | 11-1/4" | Sit in 1/4" dados |
| Adjustable shelf | 3 | 34-3/8" | 11" | 1/16" clearance each end, set back 1/4" |
| Toe kick | 1 | 34-1/2" | 3" | Between the sides, under the bottom |
| Back (1/4" ply) | 1 | 72" | 36" | Separate 1/4" sheet |
Lay out the sheet
A 4 x 8 foot sheet is 48 by 96 inches. Rip it into four strips 11-1/4 inches wide. With a 1/8-inch saw kerf, that uses 45-3/8 inches and leaves a strip about 2-5/8 inches wide. Then crosscut:
- Strips one and two: one 72-inch side each, leaving offcuts of about 23-7/8 inches.
- Strip three: top and bottom at 35 inches each, leaving about 25-7/8 inches.
- Strip four: two shelves at 34-3/8 inches (ripped to 11 inches), leaving about 27-1/8 inches.
The third shelf needs 34-3/8 inches, and no offcut is that long. The toe kick needs a 3-inch-wide strip, and the leftover rip is only 2-5/8 inches. So one sheet is not enough: you need a part sheet or a second sheet for the third shelf and the toe kick. Finding that out on screen, before the lumberyard, is the point of the exercise.
OpenCutList's cutting-diagram view and CutList Optimizer's web app both automate this nesting. In CutList Optimizer, enter the panels with their quantities, set the stock sheet to 96 x 48, set the blade kerf, and lock grain direction for parts where the face veneer must run lengthwise. It returns a layout and a cut sequence.
Check before you cut
- Grain direction: on the sides and shelves, the face grain should run along the length.
- Shelf span: a 34-3/8-inch shelf in 3/4-inch plywood can sag under a full load of books. Many builders add a solid-wood front edge, 3/4 by 1-1/2 inches, to stiffen it.
- Edge banding: list the edges that need banding (shelf fronts, side fronts, top front) so they are counted in the material order.
- Labels: print part labels and stick them on as you cut. OpenCutList generates them.
Solid-wood parts: ordering by the board foot
Sheet goods are bought by the sheet, but hardwood is sold by the board foot: a volume of 144 cubic inches, calculated with the nominal thickness. The solid-wood shelf edges suggested above are a good example. Each strip is 3/4 by 1-1/2 inches finished, milled from 4/4 (1-inch nominal) stock, and 34-3/8 inches long. One strip is 1 x 1.5 x 34.375 / 144 = about 0.36 board feet, so three strips need about 1.07 board feet. Rough lumber loses material to milling, end checks and defects, so add a waste allowance of 20 to 30 percent and order about 1.5 board feet. On larger projects, assign prices to your materials in OpenCutList so its cost estimate reflects what you will actually buy.
Which tool for which shop
For a hobby shop that uses SketchUp, OpenCutList does almost everything for free. If you work in Fusion or another CAD program, CutList Optimizer is a quick way to get sheet layouts without changing your modeler; heavier use requires a paid tier. Shops with CNC routers often skip the manual layout and nest parts in their CAM software instead.
Keep reading
The other guides on this site follow a furniture project from idea to sale.